Cisco interface operational status monitor

flipflap · Post by **flipflap** » Tue Nov 14, 2006 9:06 am

this will let you know operational status of cisco interface. with this you could monitor interface status via thold

flipflap · Post by **flipflap** » Tue Nov 14, 2006 9:10 am

sample output

flipflap · Post by **flipflap** » Tue Nov 14, 2006 9:14 am

for threshold

argon0 · Post by **argon0** » Thu Dec 21, 2006 4:46 am

OK, I tried this, but have had no joy... What is the SNMP string you are queying.. Ah I see its in the jpg... Lets see what getif gives me...

WEll getif gives me values of up and down, put WSPingPro gives me 1s and 2s...

So where is the problem...

Must be in the query...

mullstu · Post by **mullstu** » Fri Jan 05, 2007 10:15 am

I imported the XML files and then configured my devices, however my graphs are not showing any info. They are created and I can view them, but the current status show 0 for the interface.

Any chance you may know why?

cwahlin · Post by **cwahlin** » Mon Jan 08, 2007 3:39 am

I get an error in the log:

CACTID: Host[4] DS[5155] WARNING: Result from SNMP not valid. Partial Result: ...

which seems to cause my graph values to be all 0. Haven't looked any deeper so not sure why this is happening.

/Carl

argon0 · Post by **argon0** » Mon Jan 08, 2007 8:44 am

cwahlin - I get the same...

mullstu · Post by **mullstu** » Mon Jan 08, 2007 8:57 am

Going through my logs this is what I get. It is the same error for each host I am monitoring. Not sure what the cause is.

CMDPHP: Poller[0] Host[29] DS[368] WARNING: Result from SNMP not valid. Partial Result: up(1

One thing I didn't change was the interfae.xml. I left it as input instead of output. Could that be the issue?

argon0 · Post by **argon0** » Mon Jan 08, 2007 9:01 am

Could be - doesn't seem to make any difference as far as I can see!

mullstu · Post by **mullstu** » Mon Jan 08, 2007 9:04 am

I just made the change. I will post the results soon

mullstu · Post by **mullstu** » Mon Jan 08, 2007 12:28 pm

Still no luck. Any ideas?

flipflap · Post by **flipflap** » Mon Jan 08, 2007 12:58 pm

hi, can you import the files below and see what happens.

check the file "interface.xml" you should see this

<ifOperStatus>
<name>Status</name>
<method>walk</method>
<source>value</source>
[b]<direction>output</direction>[/b]
<oid>.1.3.6.1.2.1.2.2.1.8</oid>
</ifOperStatus>

direction should be output.

i use USR to test query the interfaces it returns either 1 or 2. under graph management when you turn debugging on does it say "rrdtool says: ok"?

one more thing under data template --> interface status --> data source type must be "gauge"

hope that helps

flipflap · Post by **flipflap** » Mon Jan 08, 2007 1:05 pm

also check graph template and the drop down thingy, you should see "status" there

mullstu · Post by **mullstu** » Mon Jan 08, 2007 1:44 pm

I checked all of these and everything is confiurgured and set the way you stated. Not sure why the graphiong piece isn't working

flipflap · Post by **flipflap** » Mon Jan 08, 2007 2:13 pm

what does graph debug say?

try this thrread

http://forums.cacti.net/viewtopic.php?t ... ace+status

also set poller log to debbug and look for the string 1.3.6.1.2.1.2.2.1.8. you should get an output of either 1 or 2. see attached pic

Cacti

Cisco interface operational status monitor

Cisco interface operational status monitor

Graph Info does not show anything

Who is online