HELP - NO GRAPH DISPLAY

[silven]

Hi!

can you help me, I've install a new cacti but no graph appear its only blank, I tried to turned on the debug and it is ok, your help would be very much appreciated.


RRDTool Command:

/usr/bin/rrdtool graph - \
--imgformat=PNG \
--start=-86400 \
--end=-300 \
--title="Regalia 6 - Traffic - Fa0/0" \
--rigid \
--base=1000 \
--height=120 \
--width=500 \
--alt-autoscale-max \
--lower-limit=0 \
--vertical-label="bits per second" \
DEF:a="/usr/local/apache/htdocs/cacti/rra/regalia_6_traffic_in_8.rrd":traffic_in:AVERAGE \
DEF:b="/usr/local/apache/htdocs/cacti/rra/regalia_6_traffic_in_8.rrd":traffic_out:AVERAGE \
CDEF:cdefa=a,8,* \
CDEF:cdefe=b,8,* \
AREA:cdefa#00CF00:"Inbound" \
GPRINT:cdefa:LAST:" Current\:%8.2lf %s" \
GPRINT:cdefa:AVERAGE:"Average\:%8.2lf %s" \
GPRINT:cdefa:MAX:"Maximum\:%8.2lf %s\n" \
LINE1:cdefe#002A97:"Outbound" \
GPRINT:cdefe:LAST:"Current\:%8.2lf %s" \
GPRINT:cdefe:AVERAGE:"Average\:%8.2lf %s" \
GPRINT:cdefe:MAX:"Maximum\:%8.2lf %s"

RRDTool Says:

OK

[BSOD2600]

Cacti probably isn't collecting any valid data. Turn the polling level in cacti to debug (Settings | Polling level) for one cycle and paste the output of the actual log file (./cacti/log/cacti.log). If it contains WEBLOG entries, then don't bother posting since they just clutter up the log. Turn off WEBEVENTS logging and try again.

[silven]

hi, thanks for the reply, but I already turnoff web even but still same problem, I also tried to turn the polling lever to debug. below is the result

01/17/2006 05:20:34 AM - SYSTEM STATS: Time:1.0408 Method:cmd.php Processes:1 Threads:N/A Hosts:3 HostsPerProcess:3 DataSources:19 RRDsProcessed:12
01/17/2006 05:25:02 AM - SYSTEM STATS: Time:1.0407 Method:cmd.php Processes:1 Threads:N/A Hosts:3 HostsPerProcess:3 DataSources:19 RRDsProcessed:12
01/17/2006 05:29:21 AM - SYSTEM STATS: Time:1.0509 Method:cmd.php Processes:1 Threads:N/A Hosts:3 HostsPerProcess:3 DataSources:19 RRDsProcessed:12
01/17/2006 05:29:23 AM - SYSTEM STATS: Time:1.0454 Method:cmd.php Processes:1 Threads:N/A Hosts:3 HostsPerProcess:3 DataSources:19 RRDsProcessed:12
01/17/2006 05:29:42 AM - SYSTEM STATS: Time:3.0541 Method:cmd.php Processes:1 Threads:N/A Hosts:3 HostsPerProcess:3 DataSources:19 RRDsProcessed:12
01/17/2006 05:31:44 AM - SYSTEM STATS: Time:1.0454 Method:cmd.php Processes:1 Threads:N/A Hosts:3 HostsPerProcess:3 DataSources:19 RRDsProcessed:12
01/17/2006 05:31:50 AM - SYSTEM STATS: Time:2.0785 Method:cmd.php Processes:1 Threads:N/A Hosts:3 HostsPerProcess:3 DataSources:19 RRDsProcessed:12
01/17/2006 05:31:58 AM - SYSTEM STATS: Time:3.1919 Method:cmd.php Processes:1 Threads:N/A Hosts:3 HostsPerProcess:3 DataSources:19 RRDsProcessed:12
01/17/2006 05:32:04 AM - SYSTEM STATS: Time:1.0403 Method:cmd.php Processes:1 Threads:N/A Hosts:3 HostsPerProcess:3 DataSources:19 RRDsProcessed:12
01/17/2006 07:18:59 PM - SYSTEM STATS: Time:1.0548 Method:cmd.php Processes:1 Threads:N/A Hosts:3 HostsPerProcess:3 DataSources:19 RRDsProcessed:12

hope you can help me.

thanks.

[BSOD2600]

Looks like debug isn't enabled. Try enabling it, clicking save. then disabling it, click save. Then enable it again.

[silven]

Hi,

I've already done it,

is it under setting -- poller logging level - then set to debug?

[BSOD2600]

Yes, but follow the steps I outlined.