Intro page/console homepage

[om3n]

oh my god... I spent hours assuming green was active. I'm sorry to be a hassle and thank you so much for pointing out this blunder...

[BlueDog726]

Hello I am new to cacti and intro page and was wondering if there is a way to make a graph that is in the same format as the Devices by Status graph on the default panel.

[macan]

It isn't possible now. Cacti graphs are using rrd and other graphs on intropage uses js library.

[TheWitness]

The alternate graphing engine is something I've given some thought to in recent days. It's something I wrote already using a not so open source graphing solution in the past, one that had it's own templating API and not Cacti's. The new API should simply turn Cacti's LINE:AREA:STACK into objects to be fed to the charting solution I have in mind. Right now, though Billboard is awesome, I'm leaning more towards ApexCharts, though until I dig in, I won't make that final decision.

[anarkia1976]

Hi guys @macan, i need some infos related to new control "not optimized Bulk Walk Size devices".

This is my result:

Immagine 2023-08-23 140417.jpg (19.27 KiB) Viewed 10451 times

how can i use this information?

i have made some checks but i didn't see problems related to devices with:
xxxxx - (xxxxx) (ID: 12, Bulk walk size: -1)

can you help me? thanks a lot.

[TheWitness]

xmacan, maybe we need a tip for each issue. This one is a bit more complicated to resolve. Basically, the Auto-Detect on Reindex turns out to take much more time for a re-index operation. It's better to set to Auto-Detect and Set at First Re-Index as it can greatly reduce the amount of time to perform a Re-Index.

[anarkia1976]

xmacan, maybe we need a tip for each issue. This one is a bit more complicated to resolve. Basically, the Auto-Detect on Reindex turns out to take much more time for a re-index operation. It's better to set to Auto-Detect and Set at First Re-Index as it can greatly reduce the amount of time to perform a Re-Index.

In my scenario this is the result of re-index output:

Code: Select all

Total: 0.000000, Delta: 0.000000, Auto Bulk Walk Size Selected.
Total: 0.030000, Delta: 0.020000, Tested Bulk Walk Size 1 with a response of 0.0239.
Total: 0.030000, Delta: 0.010000, Tested Bulk Walk Size 5 with a response of 0.0061.
Total: 0.030000, Delta: 0.000000, Tested Bulk Walk Size 10 with a response of 0.0030.
Total: 0.040000, Delta: 0.000000, Tested Bulk Walk Size 15 with a response of 0.0034.
Total: 0.040000, Delta: 0.000000, Bulk Walk Size selected was 10.

it seem to be no problems but the device is still flagged as problematic.

Not optimized Bulk Walk Size devices - 1919
zzzzz - (xxxxx) (ID: 12, Bulk walk size: -1)

[TheWitness]

If you run this query, the problems should be resolved:

Code: Select all

UPDATE host SET bulk_walk_size=0;

Then it'll lock in at 10 for ever afterwards.

[anarkia1976]

If you run this query, the problems should be resolved:

Code: Select all

UPDATE host SET bulk_walk_size=0;

Then it'll lock in at 10 for ever afterwards.

the witness this field/parameter shouldn't be automatically updated after every re-index?

[anarkia1976]

If you run this query, the problems should be resolved:

Code: Select all

UPDATE host SET bulk_walk_size=0;

Then it'll lock in at 10 for ever afterwards.

done, it works.

[TheWitness]

Once you've detected it once, unless something changes where it's not performing as well, there is no need to do it again. A case where you might want to set it to -1, is to see if it changes over it's life, or you get a firmware update to make it work better at larger bulk walk sizes.

[anarkia1976]

Once you've detected it once, unless something changes where it's not performing as well, there is no need to do it again. A case where you might want to set it to -1, is to see if it changes over it's life, or you get a firmware update to make it work better at larger bulk walk sizes.

thanks, good.

[macan]

xmacan, maybe we need a tip for each issue. This one is a bit more complicated to resolve. Basically, the Auto-Detect on Reindex turns out to take much more time for a re-index operation. It's better to set to Auto-Detect and Set at First Re-Index as it can greatly reduce the amount of time to perform a Re-Index.

Agree, I will add any notice

[anarkia1976]

xmacan, maybe we need a tip for each issue. This one is a bit more complicated to resolve. Basically, the Auto-Detect on Reindex turns out to take much more time for a re-index operation. It's better to set to Auto-Detect and Set at First Re-Index as it can greatly reduce the amount of time to perform a Re-Index.

Agree, I will add any notice

i have see after modification of the db string "UPDATE host SET bulk_walk_size=0;" an substantial increase in page opening and reading speed, probably when this parameter is set to "-1" slowing down db read.

[anarkia1976]

xmacan, maybe we need a tip for each issue. This one is a bit more complicated to resolve. Basically, the Auto-Detect on Reindex turns out to take much more time for a re-index operation. It's better to set to Auto-Detect and Set at First Re-Index as it can greatly reduce the amount of time to perform a Re-Index.

Agree, I will add any notice

intropage is a fantastic plugin, thanks a lot for your constant support to develop it. the last check introduced the "bulk size" keep me in the direction for resolve some problems to slow db read. thanks a lot.