No graphs and errors in logs.

[rs1]

Operating System: 2008 R2 win32
Webserver: Intel?
Cacti: 8.8a
Spine: Not sure
MySQL: 5
PHP: 5.4.1.4
RRDTool (Cygwin or Win32 build): Not sure
Net-SNMP: Not sure
Cygwin (cygwin1.dll version): Not sure
Plugin Architecture:

I'm not receiving any information in my graphs and I'm receiving a few errors in my logs. Cacti beginner!

09/11/2013 10:24:27 AM - CMDPHP: Poller[0] Host[2] DS[13] WARNING: Result from SERVER not valid. Partial Result: U
09/11/2013 10:24:27 AM - CMDPHP: Poller[0] Host[2] DS[13] SERVER: C:\inetpub\wwwroot\cacti\scripts\ss_host_disk.php ss_host_disk 127.0.0.1 2 1:161:500:10:1:public:::::: get used 4, output: U
09/11/2013 10:24:27 AM - CMDPHP: Poller[0] Host[2] DS[13] WARNING: Result from SERVER not valid. Partial Result: U
09/11/2013 10:24:27 AM - CMDPHP: Poller[0] Host[2] DS[12] SERVER: C:\inetpub\wwwroot\cacti\scripts\ss_host_disk.php ss_host_disk 127.0.0.1 2 1:161:500:10:1:public:::::: get total 3, output: U
09/11/2013 10:24:27 AM - CMDPHP: Poller[0] Host[2] DS[12] WARNING: Result from SERVER not valid. Partial Result: U
09/11/2013 10:24:27 AM - CMDPHP: Poller[0] Host[2] DS[12] SERVER: C:\inetpub\wwwroot\cacti\scripts\ss_host_disk.php ss_host_disk 127.0.0.1 2 1:161:500:10:1:public:::::: get used 3, output: U
09/11/2013 10:24:27 AM - CMDPHP: Poller[0] Host[2] DS[12] WARNING: Result from SERVER not valid. Partial Result: U
09/11/2013 10:24:27 AM - CMDPHP: Poller[0] Host[2] DS[9] SNMP: v1: 127.0.0.1, dsname: snmp_oid, oid: .1.3.6.1.4.1.23.2.28.2.7.0, output: U
09/11/2013 10:24:27 AM - CMDPHP: Poller[0] Host[2] DS[9] WARNING: Result from SNMP not valid. Partial Result: U
09/11/2013 10:24:27 AM - CMDPHP: Poller[0] WARNING: SNMP Get Timeout for Host:'127.0.0.1', and OID:'.1.3.6.1.4.1.23.2.28.2.7.0'

Any advice would be greatly appreciated! I've spent the last day searching but cannot find an answer!

[BSOD2600]

Looks like your server doesnt have an snmp agent installed, properly configured, or a firewall is blocking the traffic. you didnt notice the SNMP ERROR message in cacti for that device?

[rs1]

Thanks for your response

I have SNMP Service running under services and NET-SNMP installed. Is this correct?

I'll check documentation against config.

I saw the error but still learning

[rs1]

The minimal requirements are setup with NET-SNMP. The poller shows the devices as up? What could I check for specifically?

[rs1]

Hello, I've been looking into the SNMP service but cannot get it to work. Always getting timeouts with snmpwalk localhost, I created the config file as instructed by your documentation and the windows PATH is pointing to the correct location (I think!). Any ideas?

[BSOD2600]

I would highly recommend installing the microsoft snmp agent instead of net-snmp one. follow the MS guides on getting it installed/configured. Until a basic snmpwalk of the device works, then cacti can be used to query it.