Weathermaps not reporting properly.

[jmwhitesr31]

I have figured out the issue from my still learning Cacti post now I get a new error. It is saying the file is not reporting data. I have attached the errors below.
04/02/2013 11:07:30 AM - WEATHERMAP: Poller[0] WARNING: [Map 2] WAN Connectivity.conf: ReadData: NODE KansascitynorthLatency, target: gauge:C:/Cacti/Apache2/htdocs/cacti/rra/609/33018.rrd:avg:- on config line 126 of C:\Cacti\Apache2\htdocs\cacti\plugins\weathermap\configs\WAN Connectivity.conf had no valid data, according to WeatherMapDataSource_rrd
04/02/2013 11:07:30 AM - WEATHERMAP: Poller[0] WARNING: [Map 2] WAN Connectivity.conf: RRD ReadData: At least one of your DS names (avg and -) were not found, even though there was a valid data line. Maybe they are wrong? Valid DS names in this file are: traffic_in,traffic_out, [WMRRD06]
04/02/2013 11:07:30 AM - WEATHERMAP: Poller[0] WARNING: [Map 2] WAN Connectivity.conf: RRD ReadData: poller_output: avg is not a valid DS name for /609/33018.rrd - valid names are: traffic_in, traffic_out [WMRRD07]
04/02/2013 11:07:29 AM - WEATHERMAP: Poller[0] WARNING: [Map 2] WAN Connectivity.conf: ReadData: NODE BroomfieldLatency, target: gauge:C:/Cacti/Apache2/htdocs/cacti/rra/600/32594.rrd:avg:- on config line 126 of C:\Cacti\Apache2\htdocs\cacti\plugins\weathermap\configs\WAN Connectivity.conf had no valid data, according to WeatherMapDataSource_rrd
04/02/2013 11:07:29 AM - WEATHERMAP: Poller[0] WARNING: [Map 2] WAN Connectivity.conf: RRD ReadData: At least one of your DS names (avg and -) were not found, even though there was a valid data line. Maybe they are wrong? Valid DS names in this file are: active_ports,total_ports,active_macs,trunk_ports, [WMRRD06]
04/02/2013 11:07:29 AM - WEATHERMAP: Poller[0] WARNING: [Map 2] WAN Connectivity.conf: RRD ReadData: poller_output: /600/32594.rrd is not a valid RRD filename within this Cacti install. is C:/Cacti/Apache2/htdocs/cacti/rra [WMRRD08]
04/02/2013 11:07:29 AM - WEATHERMAP: Poller[0] WARNING: [Map 2] WAN Connectivity.conf: NODE KansascitynorthLatency has a relative position to an unknown node! [WMWARN10]
04/02/2013 11:07:29 AM - WEATHERMAP: Poller[0] WARNING: [Map 2] WAN Connectivity.conf: NODE KansascitynorthLatency has a relative position to an unknown node! [WMWARN10]
04/02/2013 11:06:29 AM - WEATHERMAP: Poller[0] WARNING: [Map 2] WAN Connectivity.conf: ReadData: NODE KansascitynorthLatency, target: gauge:C:/Cacti/Apache2/htdocs/cacti/rra/609/33018.rrd:avg:- on config line 126 of C:\Cacti\Apache2\htdocs\cacti\plugins\weathermap\configs\WAN Connectivity.conf had no valid data, according to WeatherMapDataSource_rrd
04/02/2013 11:06:29 AM - WEATHERMAP: Poller[0] WARNING: [Map 2] WAN Connectivity.conf: RRD ReadData: At least one of your DS names (avg and -) were not found, even though there was a valid data line. Maybe they are wrong? Valid DS names in this file are: traffic_in,traffic_out, [WMRRD06]
04/02/2013 11:06:29 AM - WEATHERMAP: Poller[0] WARNING: [Map 2] WAN Connectivity.conf: RRD ReadData: poller_output: avg is not a valid DS name for /609/33018.rrd - valid names are: traffic_in, traffic_out [WMRRD07]
04/02/2013 11:06:29 AM - WEATHERMAP: Poller[0] WARNING: [Map 2] WAN Connectivity.conf: ReadData: NODE BroomfieldLatency, target: gauge:C:/Cacti/Apache2/htdocs/cacti/rra/600/32594.rrd:avg:- on config line 126 of C:\Cacti\Apache2\htdocs\cacti\plugins\weathermap\configs\WAN Connectivity.conf had no valid data, according to WeatherMapDataSource_rrd
04/02/2013 11:06:29 AM - WEATHERMAP: Poller[0] WARNING: [Map 2] WAN Connectivity.conf: RRD ReadData: At least one of your DS names (avg and -) were not found, even though there was a valid data line. Maybe they are wrong? Valid DS names in this file are: active_ports,total_ports,active_macs,trunk_ports, [WMRRD06]
04/02/2013 11:06:29 AM - WEATHERMAP: Poller[0] WARNING: [Map 2] WAN Connectivity.conf: RRD ReadData: poller_output: /600/32594.rrd is not a valid RRD filename within this Cacti install. is C:/Cacti/Apache2/htdocs/cacti/rra [WMRRD08]
04/02/2013 11:06:29 AM - WEATHERMAP: Poller[0] WARNING: [Map 2] WAN Connectivity.conf: NODE KansascitynorthLatency has a relative position to an unknown node! [WMWARN10]
04/02/2013 11:06:29 AM - WEATHERMAP: Poller[0] WARNING: [Map 2] WAN Connectivity.conf: NODE KansascitynorthLatency has a relative position to an unknown node! [WMWARN10]
04/02/2013 11:05:29 AM - WEATHERMAP: Poller[0] WARNING: [Map 2] WAN Connectivity.conf: ReadData: NODE KansascitynorthLatency, target: gauge:C:/Cacti/Apache2/htdocs/cacti/rra/609/33018.rrd:avg:- on config line 126 of C:\Cacti\Apache2\htdocs\cacti\plugins\weathermap\configs\WAN Connectivity.conf had no valid data, according to WeatherMapDataSource_rrd
04/02/2013 11:05:29 AM - WEATHERMAP: Poller[0] WARNING: [Map 2] WAN Connectivity.conf: RRD ReadData: At least one of your DS names (avg and -) were not found, even though there was a valid data line. Maybe they are wrong? Valid DS names in this file are: traffic_in,traffic_out, [WMRRD06]

PLEASE advise...

[Howie]

On line 126 of your config file, you have:

TARGET gauge:C:/Cacti/Apache2/htdocs/cacti/rra/609/33018.rrd:avg:-

Code: Select all

 [Map 2] WAN Connectivity.conf: RRD ReadData: At least one of your DS names (avg and -) were not found, even though there was a valid data line. Maybe they are wrong? Valid DS names in this file are: traffic_in,traffic_out, [WMRRD06] 

But the rrd file you are referring to doesn't have a data source inside it called 'avg'.

It has one called 'traffic_in' and one called 'traffic_out'.

So you need to change your TARGET to either:

TARGET gauge:C:/Cacti/Apache2/htdocs/cacti/rra/609/33018.rrd:traffic_in:-

or

TARGET gauge:C:/Cacti/Apache2/htdocs/cacti/rra/609/33018.rrd:traffic_out:-

Depending on which of those values you want to appear in the map.

If it's a link, then you probably actually want both:

TARGET gauge:C:/Cacti/Apache2/htdocs/cacti/rra/609/33018.rrd:traffic_in:traffic_out

and good news, the default DS names are traffic_in and traffic_out (because that's what most Cacti traffic graphs use), so you can change that to:

TARGET gauge:C:/Cacti/Apache2/htdocs/cacti/rra/609/33018.rrd

Finally, if it IS the standard Cacti traffic graph template that you are using, you shouldn't use the gauge: prefix, otherwise your results will be 1/8 of the correct value (gauge disables the default behaviour of turning byte-counters into bits-per-second by multiplying by :

TARGET C:/Cacti/Apache2/htdocs/cacti/rra/609/33018.rrd