all Graph are empty

Post general support questions here that do not specifically fall into the Linux or Windows categories.

Moderators: Developers, Moderators

Post Reply
lester
Posts: 9
Joined: Sat Dec 06, 2008 9:27 am

all Graph are empty

Post by lester »

Hi,
I am new user on cacti
I have installed cacti 0.8.7b on debian etch

Wen i use snmpwalk the result is Ok.
the poller are running

this is a cacti log :

Code: Select all

12/06/2008 03:50:02 PM - POLLER: Poller[0] NOTE: Poller Int: '300', Cron Int: '300', Time Since Last: '301', Max Runtime '298', Poller Runs: '1'
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[8] WARNING: Result from SNMP not valid.  Partial Result: 
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[8] SNMP: v1: MyHost, dsname: users, oid: .1.3.6.1.2.1.25.1.5.0, output: U
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[9] WARNING: Result from SNMP not valid.  Partial Result: 
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[9] SNMP: v1: MyHost, dsname: proc, oid: .1.3.6.1.2.1.25.1.6.0, output: U
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[10] WARNING: Result from SNMP not valid.  Partial Result: 
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[10] SNMP: v1: MyHost, dsname: cpu_nice, oid: .1.3.6.1.4.1.2021.11.51.0, output: U
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[11] WARNING: Result from SNMP not valid.  Partial Result: 
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[11] SNMP: v1: MyHost, dsname: cpu_system, oid: .1.3.6.1.4.1.2021.11.52.0, output: U
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[12] WARNING: Result from SNMP not valid.  Partial Result: 
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[12] SNMP: v1: MyHost, dsname: cpu_user, oid: .1.3.6.1.4.1.2021.11.50.0, output: U
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[13] WARNING: Result from SNMP not valid.  Partial Result: 
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[13] SNMP: v1: MyHost, dsname: load_1min, oid: .1.3.6.1.4.1.2021.10.1.3.1, output: U
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[14] WARNING: Result from SNMP not valid.  Partial Result: 
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[14] SNMP: v1: MyHost, dsname: load_15min, oid: .1.3.6.1.4.1.2021.10.1.3.3, output: U
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[15] WARNING: Result from SNMP not valid.  Partial Result: 
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[15] SNMP: v1: MyHost, dsname: load_5min, oid: .1.3.6.1.4.1.2021.10.1.3.2, output: U
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[16] WARNING: Result from SNMP not valid.  Partial Result: 
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[16] SNMP: v1: MyHost, dsname: esx_mem_cos, oid: .1.3.6.1.4.1.6876.3.2.2.0, output: U
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[17] WARNING: Result from SNMP not valid.  Partial Result: 
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[17] SNMP: v1: MyHost, dsname: esx_mem_free, oid: .1.3.6.1.4.1.6876.3.2.3.0, output: U
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[18] WARNING: Result from SNMP not valid.  Partial Result: 
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[18] SNMP: v1: MyHost, dsname: esx_mem_total, oid: .1.3.6.1.4.1.6876.3.2.1.0, output: U
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[25] SNMP: v1: MyHost, dsname: bladecent_fan1, oid: .1.3.6.1.4.1.2.3.51.2.2.3.1.0, output: 57
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[26] SNMP: v1: MyHost, dsname: bladecent_fan2, oid: .1.3.6.1.4.1.2.3.51.2.2.3.2.0, output: 57
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[27] SNMP: v1: MyHost, dsname: bladecent_ac_pwr, oid: .1.3.6.1.4.1.2.3.51.2.2.10.5.1.2.0, output: 1740
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[28] SNMP: v1: MyHost, dsname: bladecent_dc_pwr, oid: .1.3.6.1.4.1.2.3.51.2.2.10.5.1.1.0, output: 7040
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[29] SNMP: v1: MyHost, dsname: bladecent_allpower1, oid: .1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.8.1.0, output: 2368
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[30] SNMP: v1: MyHost, dsname: bladecent_poweruse1, oid: .1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.10.1, output: 1137
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[31] SNMP: v1: MyHost, dsname: bladecent_rempower1, oid: .1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.9.1.0, output: 1152
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[32] SNMP: v1: MyHost, dsname: bladecent_allpower2, oid: .1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.8.2.0, output: 400
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[33] SNMP: v1: MyHost, dsname: bladecent_rempower2, oid: .1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.9.2.0, output: 3120
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[34] SNMP: v1: MyHost, dsname: bladecent_fronttemp, oid: .1.3.6.1.4.1.2.3.51.2.2.1.5.1.0, output: 19.00
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[35] SNMP: v1: MyHost, dsname: bladecent_platemp, oid: .1.3.6.1.4.1.2.3.51.2.2.1.1.2.0, output: 32.00
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[36] SNMP: v1: MyHost, dsname: bladecent_therm_out, oid: .1.3.6.1.4.1.2.3.51.2.2.10.5.1.3.0, output: 5936.880000
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[37] SNMP: v1: MyHost, dsname: bladecent_plus18V, oid: .1.3.6.1.4.1.2.3.51.2.2.2.1.8.0, output: +1.77
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[38] SNMP: v1: MyHost, dsname: bladecent_plus12V, oid: .1.3.6.1.4.1.2.3.51.2.2.2.1.3.0, output: +11.78
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[39] SNMP: v1: MyHost, dsname: bladecent_plus25V, oid: .1.3.6.1.4.1.2.3.51.2.2.2.1.6.0, output: +2.48
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[40] SNMP: v1: MyHost, dsname: bladecent_plus33V, oid: .1.3.6.1.4.1.2.3.51.2.2.2.1.2.0, output: +3.26
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[2] DS[41] SNMP: v1: MyHost, dsname: bladecent_plus5V, oid: .1.3.6.1.4.1.2.3.51.2.2.2.1.1.0, output: +4.84
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[3] DS[19] CMD: perl /var/www/cacti/scripts/linux_memory.pl MemFree:, output: 1805336
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[3] DS[20] CMD: perl /var/www/cacti/scripts/linux_memory.pl SwapFree:, output: 409616
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[3] DS[21] CMD: perl /var/www/cacti/scripts/loadavg_multi.pl, output: 1min:0.00 5min:0.00 10min:0.00
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[3] DS[22] CMD: perl /var/www/cacti/scripts/unix_users.pl , output: 1
12/06/2008 03:50:02 PM - CMDPHP: Poller[0] Host[3] DS[23] CMD: perl /var/www/cacti/scripts/unix_processes.pl, output: 60
12/06/2008 03:50:03 PM - CMDPHP: Poller[0] Host[3] DS[24] CMD: perl /var/www/cacti/scripts/query_unix_partitions.pl  get used /dev/sda1, output: 1231368
12/06/2008 03:50:03 PM - CMDPHP: Poller[0] Host[3] DS[24] CMD: perl /var/www/cacti/scripts/query_unix_partitions.pl  get available /dev/sda1, output: 6220816
12/06/2008 03:50:03 PM - CMDPHP: Poller[0] Time: 0.8258 s, Theads: N/A, Hosts: 2
12/06/2008 03:50:03 PM - SYSTEM STATS: Time:1.1510 Method:cmd.php Processes:1 Threads:N/A Hosts:3 HostsPerProcess:3 DataSources:35 RRDsProcessed:34
Can you help me ?

Thank
Top
User avatar
gandalf
Developer
Posts: 22383
Joined: Thu Dec 02, 2004 2:46 am
Location: Muenster, Germany
Contact:
Contact gandalf

Post by gandalf »

Please see 2md link of my sig for the failing stuff. But some queries seem to be fine; at least valid data is returned
Reinhard
Top
hangas
Posts: 9
Joined: Thu Nov 27, 2008 9:16 pm

Re: all Graph are empty

Post by hangas »

Hi, I have the same problem and with the same OID.
I did nor sorted it out yet, but I have a clue on what the problem is.

I have two BladecenterE with the same firmware version, however one is an older model.
On the 2009 model the OID value comes as:

Code: Select all

SNMPv2-SMI::enterprises.2.3.51.2.2.10.5.1.2.0 = STRING: "1237W"
and is parsed and plotted correctly.
On the newer 2011 model e comes as

Code: Select all

SNMPv2-SMI::enterprises.2.3.51.2.2.10.5.1.2.0 = STRING: "464W (+/- 3.0%)"
I guess the stupid (+/- 3.0%) is choking the parser.

I already took a look on lib/data_query.php to check if it was some obvious regex that could be "fixed" but it was not obvious to me.
Any more clues?
Top
hangas
Posts: 9
Joined: Thu Nov 27, 2008 9:16 pm

Re: all Graph are empty

Post by hangas »

Hi, I have the same problem and with the same OID.
I did nor sorted it out yet, but I have a clue on what the problem is.

I have two BladecenterE with the same firmware version, however one is an older model.
On the 2009 model the OID value comes as:

Code: Select all

SNMPv2-SMI::enterprises.2.3.51.2.2.10.5.1.2.0 = STRING: "1237W"
and is parsed and plotted correctly.
On the newer 2011 model e comes as

Code: Select all

SNMPv2-SMI::enterprises.2.3.51.2.2.10.5.1.2.0 = STRING: "464W (+/- 3.0%)"
I guess the stupid (+/- 3.0%) is choking the parser.

I already took a look on lib/data_query.php to check if it was some obvious regex that could be "fixed" but it was not obvious to me.
Any more clues?
Top
User avatar
gandalf
Developer
Posts: 22383
Joined: Thu Dec 02, 2004 2:46 am
Location: Muenster, Germany
Contact:
Contact gandalf

Re: all Graph are empty

Post by gandalf »

hangas wrote:

Code: Select all

SNMPv2-SMI::enterprises.2.3.51.2.2.10.5.1.2.0 = STRING: "464W (+/- 3.0%)"
I guess the stupid (+/- 3.0%) is choking the parser.
In this case, you will require a Data Input Method to do the regexp in your script.
BTB: I hate "STRING" type output where INTEGER would be fine.
R.
Top
Post Reply

Return to “Help: General”

Who is online

Users browsing this forum: No registered users and 6 guests