Ok I am begging for pecentage :)

[Bisonlux]

I am sure there is a bug in Cacti, because the first time I make a graph, I have the same behaviour (same percentage values for both data sources).
[see my post: Posted: Wed Dec 31, 2003 6:54 pm Post subject: Percent and a little bug]

If a have time I will check the php code where the rrdtool graph is generated.

[TFC]

TFC,

The zip file contains all the definitions/configurations to display the graph as you post in the last days.

Give me a feedback with your result.

Good luck !

Hi again,
I did your instruction. And I read your answer in
http://www.raxnet.net/board/viewtopic.php?t=3030
I changed my rrd.php file. But graph still divide max value as 100M
You can see the graph that some wrong calculation exists
--------------------
For example:
For calculating Max. Inbound Utility:
(62,13Mbit/155Mbit)*100=40.08% (this is correct calculation)
(62,13Mbit/100Mbit)*100=62.13% (this is our cdef calculation)
I mean our cdef still sees max value as 100Mbit not 155Mbit.
Help Us Ian

[scurcio]

I see where you have the percentage in the bottom of the graph but can you present the graph itself in a percentage ?

I have a gigabit line and I just want to say its gigabit and then have the graph itself show 1-100 percent in use and then have the bottom show min/average/max in percent.

[Bisonlux]

Check this out: http://www.raxnet.net/board/viewtopic.php?t=2994

You have an example with a graph.

[scurcio]

Check this out: http://www.raxnet.net/board/viewtopic.php?t=2994

You have an example with a graph.

I want to have the graph it self show from 0-100% and then have it show the percentage in utilization be on the graph instead of below in just the numbers. I need this so a manager can easily understand it.

The graphical part of the graph should show 0-100% utilization and then the bottom of the graph can show the mbits or kbits in min/average/max.

[TFC]

Finally
My problem has been solved. Thank you Bisonlux and Ian.
I am really very grateful to you.
After 0.8.5, percentage problem completely solverd.
In attachment you can see last version graph.

[skt]

Hello TFC,

Do you have the xml files for tese new graphs? If you do, can you please post them?

Thanks,

SKT

[TFC]

Hello TFC,

Do you have the xml files for tese new graphs? If you do, can you please post them?

Thanks,

SKT

Nope,
But I can post the summary tomorrow

[nydoofus]

Hello TFC,

Do you have the xml files for tese new graphs? If you do, can you please post them?

Thanks,

SKT

Nope,
But I can post the summary tomorrow

Could you? I would love to have percentage capability.

[anthony.warren]

If you could post the XML files, it would make my day.

This addition would be really helpful to me.

Anthony Warren

[TFC]

I don't have XML file.But, if you look at the attachement, I hope it will help you.

[skt]

I tried your posted instructions. When applying the GPRINT Preset to the graph template all of my bits / sec graphs break. Any ideas?

[TFC]

I tried your posted instructions. When applying the GPRINT Preset to the graph template all of my bits / sec graphs break. Any ideas?

can you debug graph? and post it the error..

[skt]

Here it is:

CDEF:cdefa=a,8,* \
CDEF:cdefe=b,8,* \
CDEF:cdefbd=b,8,*,100000000,/,100,* \
AREA:cdefa#00CF00:"Inbound" \
GPRINT:cdefa:MAX:" Maximum\:%8.2lf %s" \
GPRINT:cdefa:AVERAGE:"Average\:%8.2lf %s" \
GPRINT:cdefa:LAST:"Current\:%8.2lf %s\n" \
LINE1:cdefe#002A97:"Outbound" \
GPRINT:cdefe:MAX:"Maximum\:%8.2lf %s" \
GPRINT:cdefe:AVERAGE:"Average\:%8.2lf %s" \
GPRINT:cdefe:LAST:"Current\:%8.2lf %s\n" \
COMMENT:"Max Bandwidth (bps): 45000000\n" \
COMMENT:"Interface IP Address: 144.228.154.150\n" \
COMMENT:"Last Updated: Tue 17 Feb 16:00:14 CST 2004\n" \
HRULE:45000000#FF0000:"" \
HRULE:45000000#FF0000:"" \
GPRINT:cdefbd:LAST:"Current Traffic Out Percent\:(%6.2If%%)"

Thanks,

SKT

[TFC]

Here is mine :

/usr/local/rrdtool-1.0.46/bin/rrdtool graph - \
--imgformat=PNG \
--start=end-604800 \
--end=1077090885 \
COMMENT:"From 2004-02-11 07:54:45 to 2004-02-18 07:54:45\c" \
COMMENT:"Graph Generated at 2004-02-18 07:54:45\c" \
--title="M 2B 7507 - Traffic - Fa1/1/0" \
--rigid \
--base=1000 \
--height=140 \
--width=500 \
--alt-autoscale-max \
--lower-limit=0 \
--vertical-label="bits per second" \
DEF:a="/www/htdocs/cacti/rra/m_2b_7507_traffic_in_78.rrd":traffic_in:AVERAGE \
DEF:b="/www/htdocs/cacti/rra/m_2b_7507_traffic_in_78.rrd":traffic_out:AVERAGE \
CDEF:cdefa=a,8,* \
CDEF:cdefe=b,8,* \
CDEF:cdefj=a,8,*,1000000000,/,100,* \
CDEF:cdefbb=a,8,*,1000000000,/,100,* \
AREA:cdefa#00CF00:"Inbound" \
GPRINT:cdefa:LAST:" Current\:%8.2lf %s" \
GPRINT:cdefa:AVERAGE:"Average\:%8.2lf %s" \
GPRINT:cdefa:MAX:"Maximum\:%8.2lf %s\n" \
LINE1:cdefe#002A97:"Outbound" \
GPRINT:cdefe:LAST:"Current\:%8.2lf %s" \
GPRINT:cdefe:AVERAGE:"Average\:%8.2lf %s" \
GPRINT:cdefe:MAX:"Maximum\:%8.2lf %s" \
COMMENT:"--INBOUND\n" \
GPRINT:cdefj:LAST:"Current Util \:(%6.2lf%%)\n" \
GPRINT:cdefj:AVERAGE:"Average Util \:(%6.2lf%%)\n" \
GPRINT:cdefbb:MAX:"Max. Util \:(%6.2lf%%)\n" \
COMMENT:"--OUTBOUND\n" \
GPRINT:cdefbb:LAST:"Current Util \:(%6.2lf%%)\n" \
GPRINT:cdefbb:AVERAGE:"Average Util \:(%6.2lf%%)\n" \
GPRINT:cdefbb:MAX:"Max. Util \:(%6.2lf%%)\n" \
COMMENT:"-Desc: 8540_4A Baglant -Speed: 100000000 bps -IP Address: 10.200.98.9\n"

Please go to graph management section. Select one of the interface that you can not see and click it. Then click "Turn On Graph Debup Mode." link. And copy here what you see.