Cacti

How can i pass the mysql port with the syslog plugin as we run mysql on 3406 and i believe the syslog plugin uses the default 3306 somewhere?

Thanks

Nigel

using the templates hrStorageTable i am graphing Total and Used space fine. I would like to add a line showing 80% total space to the graph. I am gathering i need a HRULE but the only examples are for bits /bytes ie |80:bits:0:max| there is a CDEF that gets applied to the data sources but adding thi...

Bingo all working now with the non standard mysql port. Thanks. Will it be possible to choose the fonts sizes? only some of our graph titles are longer than the graph image so get cut off.

Nigel

To do the original install back in November 2008. but each cacti upgrade has been run as per the readme ie backup DB, rename old cacti folder etc. I have upgraded to 8.7.d with plugin 2.4 but still same result. the only obvious thing that is different is the MYSQL instance runs on port 3406, do you ...

Yes under the cacti\include directory is the config.php with the correct mysql settings. This is a iis / windows box if that makes a difference?

Thanks

phalek wrote:the plugin tries to retrieve the database settings from the config.php file, do you have that and is there some valid data in there ?

When selecting the PDF icon on a graph tree page, i get unable to connect to MYSQL on localhost......

have i missed out a step? i have added both plugin directories under the cacti\plugin folder. installed and enabled them in cacti. replaced the htmlgraph.php with the 8.7b.

Thanks

calculate the error percentage based on packet rate and error rate? I currently need to monitor a 1gb link between to Cisco 6513 Cat's and record the error percentage, reason is our ISP guarantees 99.98% packet delivery on this link so we would like to measure is the error rate goes over 0.02% if th...

OK here you go for starters



There are no ACL restricting access to the CAM/BRIDGE info?

can i SNMP walk the bridge info to see if its returning the correct data?

I have configured 6513 running CatOS with 6000 MSFC's and theses are returning data correctly, but when i add the 4500 as switch/hub or switch/router using scanIOS or scan CatOS i only get back the trunk port to another cat and no user ports ie 4 x 4248 cards only the ten gig interface?

Thanks

It is possible ... The problem is that telnet protocol in windows do not read the input in not interactive mode. There are several solutions, but the easiest without programmation (C,WSscript) is with cygwin. Thanks, but when we log in to a router we dont supply a username, then once logged in we h...

I change from V2 to V1 and sort of worked, these were Cisco 7200 routers. Problem is now out end as no RW community string, no SSH, i i dont think there is a command line plink equivilent for telnet with login / enable access etc?

Thanks

In the log i see:

Error: Cannot download: 172.16.3.4 not activ.

What does not activ mean and how can i activ the device?

Im running PHP TFTP on win platform, I have checked the pure TFTP box and entered the IP of out TFTP server.

Thanks

Yours Confused as Ever

Nigel

OK i am getting somewhere. I have editied the Data templata for interface - traffic to set the step to 900 ( 15 minutes ), poller runs ever 1 minute and RRA's have steps of 1, so i am guessing that the RRA will store data at 1 minute intervals, but the graph will display the ( in this case AVERAGE )...

Is it possible to graph as per the first post 0-100% on a positive only graph, but showing incoming and outcoming ie: incoming 0-70% green, area, average incoming 70-100% red, area, average outcoming 0-70% blue, line1 outcoming 70-100% red, line1 so basicly the graph would look like the standard tra...

i have set up a utilization graph as per http://forums.cacti.net/viewtopic.php?t=8520 i have set the interval for the graph th 15 mins average. See attached shot. i was wondering if it is possible to count up all 15 min intervals that exceed 60% ( shown in red on the graph ). ie GPRINT 60%-100% coun...