I know the difference - but did a reboot so the 'Message Log' is cleared.



I will do this, if more WUs fail.



--//--





That with the SWAP is new for me...
So i had to configure at least 2 GB when i install the new Xubuntu Precise?
Or what size is recommended

Sorry, my fault! I misunderstood RS...

I bring up the last 3 of them:

Result Name: E207542_ 956_ C.27.C24H14OS2.01879920.0.set1d06_ 0--

<core_client_version>6.12.33</core_client_version>
<![CDATA[
<message>
process exited with code 195 (0xc3, -61)
</message>
<stderr_txt>
INFO: No state to restore. Start from the beginning.
[08:51:11] Number of jobs = 16
[08:51:11] Starting job 0,CPU time has been restored to 0.000000.
[08:51:11] Starting new Job
[08:51:11] Qink name = fldman
Application exited with RC = 0xb
[ERROR] Failed to open either source or destination files while copying C.27.C24H14OS2.01879920.0.noopt.bp86.sto6g.n.sp/53.0 to C.27.C24H14OS2.01879920.0.noopt.bp86.sto6g.n.sp.53.0. Error: 2
[08:51:12] Finished Job #0
08:51:12 (12028): called boinc_finish

</stderr_txt>
]]>

----------------------------------------------------------------------------------------------------------

Result Name: E207542_ 943_ C.26.C20H8S4Se2.01760109.4.set1d06_ 0--

<core_client_version>6.12.33</core_client_version>
<![CDATA[
<message>
process exited with code 195 (0xc3, -61)
</message>
<stderr_txt>
INFO: No state to restore. Start from the beginning.
[08:49:16] Number of jobs = 16
[08:49:16] Starting job 0,CPU time has been restored to 0.000000.
[08:49:16] Starting new Job
[08:49:17] Qink name = fldman
Application exited with RC = 0xb
[ERROR] Failed to open either source or destination files while copying C.26.C20H8S4Se2.01760109.4.noopt.bp86.sto6g.n.sp/53.0 to C.26.C20H8S4Se2.01760109.4.noopt.bp86.sto6g.n.sp.53.0. Error: 2
[08:49:17] Finished Job #0
08:49:17 (12013): called boinc_finish

</stderr_txt>
]]>

-------------------------------------------------------------------------------------------------------

Result Name: E207542_ 790_ C.26.C22H14N2SeSi.01824233.2.set1d06_ 1--

<core_client_version>6.12.33</core_client_version>
<![CDATA[
<message>
process exited with code 195 (0xc3, -61)
</message>
<stderr_txt>
INFO: No state to restore. Start from the beginning.
[08:44:57] Number of jobs = 16
[08:44:57] Starting job 0,CPU time has been restored to 0.000000.
[08:44:58] Starting new Job
Application exited with RC = 0x100
[ERROR] Failed to open either source or destination files while copying C.26.C22H14N2SeSi.01824233.2.noopt.bp86.sto6g.n.sp/53.0 to C.26.C22H14N2SeSi.01824233.2.noopt.bp86.sto6g.n.sp.53.0. Error: 2
[08:44:58] Finished Job #0
08:44:58 (11995): called boinc_finish

</stderr_txt>
]]>


Seems for me every time the same error
"Failed to open either source or destination files while copying"

So, i looked on the 4th - there is an difference:


Result Name: E207538_ 778_ C.27.C23H14N2S2.01862558.3.set1d06_ 1--

<core_client_version>6.12.33</core_client_version>
<![CDATA[
<message>
process exited with code 195 (0xc3, -61)
</message>
<stderr_txt>
INFO: No state to restore. Start from the beginning.
[05:10:23] Number of jobs = 16
[05:10:23] Starting job 0,CPU time has been restored to 0.000000.
[05:10:23] Starting new Job
[05:10:23] Qink name = fldman
[05:10:23] Qink name = gesman
[05:10:23] Qink name = scfman
Application exited with RC = 0xb
[05:10:27] Finished Job #0
05:10:27 (11548): called boinc_finish

</stderr_txt>
]]>

This 2 errors are mixed up throw the hole WUs.

Thanks for your help!

BTW:
In the System Requirements are only "Disc Space" and "Memory Available" listed, nothing about Swap-Space.
Maybe i need to extend the root-Partition a bit, but with installed applications from BOINC are more than 4 GB left.

Just re-checked it again:
Number of workunits per host for The Clean Energy Project - Phase 2?
1 - Default

So it IS a probably a HDD space problem and i have to rethink my partitions layout for the new installation.

Thanks again for your fast and helpfull reponse, SekeRob.

16 lines is not 30 ;-), but anyhow, had you said Linux in your original post, then stopping the daemon with "sudo service boinc-client stop" in terminal would have been part of my response. Did that routinely. Whilst shutting down from GUI, hit the Esc key to see all the close down messages and if any signal 11-15 are in there. BOINC simply does not like being starved of cycles for longer than 29 seconds and that can occur. Try the command, then wait for the confirm of 2 lines prior to booting if badness happens still.

My latest Linux clean install, now with kernel 3.0.0.19 is well behaved, but must say that I got so frustrated with CEP2 on Linux (poor efficiency, particular when using system), that it's now only run when booted in W7-64, which gives me 99% efficiency (1% gap between wallclock and CPU time recorded).

--//--

P.S. Seems Canonical's Shuttleworth decided to hide the Hibernate functionality in Ubuntu 12.04 (did find out how to hack it back in on my 12.04 laptop before reading that). He thought too many had problems with it, hardware not coping (well his software is to blame for that I think). Read http://askubuntu.com/questions/94754/how-to-enable-hibernation-in-12-04 and http://askubuntu.com/questions/111669/hiberna...press-laptop-power-button

Cramped for disk space. My default profile for disk usage is: on BOINC data drives that typically have several hundred gig free.

Beyond your lack of physical free disk space, with most other software the indication that BOINC should use at most 0.00GB of disk space would ordinarily be a red flag to me, but BOINC uses "0" to indicate unlimited quite often so I can't call that one way or the other (particularly as I'm not running under a 'nix). I don't know if BOINC is seeing "I'm not allowed to use any disk space!", or "I'm allowed to use all of the disk space, such as it is!".

So I'd post the pertinent lines from your device profile for sekerob's more qualified perusal.